Quick Link
Quick Contact
Address
Room 13G, No. 888 Wanhangu Road, Jing'an District, Shanghai, China
Tel
86--13912788181
Our Newsletter
Subscribe to our newsletter for discounts and more.
Our plastic air operated diaphragm pump is designed for transferring corrosive liquids, chemicals, wastewater and slurry in industrial environments. Driven by compressed air rather than an electric motor, this pneumatic diaphragm pump has no rotating drive shaft or conventional dynamic shaft seal, helping reduce leakage risks during chemical handling. Plastic pump body options such as PP and PVDF are available, while diaphragm, ball and seat materials can be selected according to the pumped medium.
With eight models covering 1/4-inch to 3-inch ports, the pump offers maximum flow rates from 27 to 1,060 L/min and maximum discharge heads of 70 to 84 m, depending on the model. It supports dry and wet self-priming, can handle suspended particles within the specified passage size, and allows flow adjustment through compressed-air control. It is suitable for chemical transfer, electroplating wastewater, scrubber circulation and selected hazardous-area applications after appropriate safety assessment.
Factories handling acids, alkalis, solvents and wastewater often face chemical leakage, seal damage and pump blockage. Conventional electric centrifugal pumps may require special motor protection in hazardous locations and can suffer from mechanical seal wear when handling corrosive liquids. Suspended particles may also block narrow flow passages or damage rotating components.
Operators may additionally need to transfer liquid from drums, tanks or collection pits where suction conditions vary. A fixed-speed pump can be difficult to adjust when production demand changes. Choosing an unsuitable diaphragm or valve material may cause swelling, cracking or premature failure.
An air operated double diaphragm pump uses compressed air to move liquid through alternating pumping chambers. Its sealless operating design eliminates the conventional rotating shaft seal, reducing one common source of chemical leakage. The pump can handle intermittent operation and dry-running conditions, although prolonged dry running may increase wear and air consumption.
PP and PVDF body options provide material choices for different chemical services. PTFE, EPDM, nitrile and Viton diaphragms, together with suitable valve balls and seats, can be selected according to chemical compatibility. The air-driven design also allows operators to regulate output by adjusting air pressure and supply flow.
For hazardous locations, assess the complete installation, including static grounding, conductive components, compressed-air equipment and applicable explosion-protection requirements. Do not assume that every plastic pump configuration is automatically certified for explosive atmospheres.
| Model | Port (in) | Max Flow (L/min) | Max Head (m) | Dry / Wet Suction (m) | Max Particle (mm) | Max Air (bar) | Air Inlet (in) |
|---|---|---|---|---|---|---|---|
| DBL-06 | 1/4 | 27 | 70 | 2.1 / 3.7 | 1.6 | 7 | 1/4 |
| DBL-10 | 3/8 | 27 | 70 | 2 / 6.4 | 1.6 | 7 | 3/8 |
| DBL-15 | 1/2 | 57 | 84 | 4 / 7.6 | 2.5 | 8.4 | 3/8 |
| DBL-20 | 3/4 | 57 | 84 | 4 / 7.6 | 2.5 | 8.4 | 3/8 |
| DBL-25 | 1 | 157 | 84 | 4 / 8 | 4 | 8.4 | 1/2 |
| DBL-40 | 1.5 | 358 | 84 | 5 / 8 | 5 | 8.4 | 1/2 |
| DBL-50 | 2 | 587 | 84 | 5 / 8 | 6 | 8.4 | 1/2 |
| DBL-80 | 3 | 1,060 | 84 | 5 / 8 | 9.4 | 8.4 | 3/4 |
Values are maximum reference specifications, not guaranteed simultaneous operating points. Actual flow depends on air pressure, air consumption, discharge head, liquid viscosity and installation conditions.
Industrial waste gas scrubber and spray tower circulation
Acid and alkali chemical transfer
Electroplating wastewater collection and transfer
Industrial wastewater and slurry handling
Chemical tank unloading and liquid transfer
Solvent handling in appropriately assessed hazardous areas
Industrial cleaning and surface treatment processes
Compressed air enters the air distribution system and pushes one diaphragm forward, forcing liquid out of its chamber. At the same time, the opposite chamber draws liquid through its inlet check valve. The air distribution valve then switches direction, causing the two diaphragms to alternate their movements.
Inlet and outlet check valves control liquid flow direction, while the reciprocating diaphragm action produces continuous pumping. Since there is no rotating impeller, the pump can handle certain suspended solids according to its specified free passage. Flow can be adjusted by regulating compressed-air pressure and supply volume.
Determine flow and discharge head: Provide the required operating flow and total system head. Do not select solely by maximum flow rate.
Match the port size: Choose from 1/4-inch to 3-inch connections according to pipeline dimensions and required capacity.
Check particle size: Compare the maximum solid particle diameter with the selected model's allowable passage.
Select compatible materials: Confirm the chemical name, concentration and temperature before choosing PP, PVDF, PTFE, EPDM, nitrile, Viton or other available components.
Verify compressed-air supply: Check operating pressure, air consumption, compressor capacity and air inlet connection.
Review suction conditions: Confirm dry or wet suction lift, liquid level, pipe length and liquid viscosity.
Assess hazardous-area safety: Specify the site classification and required grounding or certification before ordering.
1. Can an air operated diaphragm pump run dry?
Yes. It can tolerate dry-running conditions better than many mechanically sealed pumps. However, prolonged dry running may increase wear and compressed-air consumption.
2. Is this pump suitable for explosive areas?
Its pneumatic drive avoids the need for an electric drive motor, but this alone does not establish explosion protection. Static grounding, material selection, installation and applicable certification must be checked.
3. Can it transfer acid and alkali liquids?
Yes, with a compatible pump body, diaphragm, ball and seat material. Confirm chemical concentration and operating temperature before ordering.
4. Can it handle wastewater containing solid particles?
Yes. The listed models support maximum particle sizes from 1.6 to 9.4 mm. Confirm particle shape, concentration and abrasiveness for your application.
5. How is the flow rate controlled?
Flow is adjusted by regulating compressed-air pressure and supply volume. Actual output also depends on discharge head and liquid properties.
6. What is the maximum suction lift?
The listed dry suction lift ranges from 2 to 5 m, while wet suction lift ranges from 3.7 to 8 m, depending on the model and operating conditions.
7. Can different diaphragm and valve materials be combined?
Yes. Body, diaphragm, ball and seat materials can be configured separately where supported by the model. Provide the liquid details so the material combination can be checked before purchase.