Quick Link
Quick Contact
Address
Room 13G, No. 888 Wanhangu Road, Jing'an District, Shanghai, China
Tel
86--13912788181
Our Newsletter
Subscribe to our newsletter for discounts and more.
Our explosion proof FRPP self priming pump is designed for industrial chemical transfer, electroplating wastewater handling, acid washing processes and waste gas scrubber circulation. Its pump head is made of injection-moulded black FRPP, offering corrosion resistance for many acid and alkali applications. The horizontal self priming design helps operators restart the pump without manually filling the entire suction line, provided the pump casing retains the required priming liquid.
Available in 0.5–7.5 HP configurations, this chemical self priming pump supports 40 × 40 mm, 50 × 50 mm and 75 × 75 mm inlet and outlet connections. Single-phase and three-phase options are available depending on the model, with 50 Hz and selected 60 Hz configurations. An explosion-proof motor can be specified for suitable hazardous-area applications. Titanium or plastic fasteners are available for selected chemical conditions.
Industrial operators may encounter several problems when transferring corrosive liquids. Conventional pumps can require repeated manual priming after maintenance or air enters the suction line. Acid vapour and chemical splashes may accelerate corrosion around exposed metal components. Fine particles in electroplating wastewater can increase wear on internal components, while unsuitable pump materials may deform or deteriorate under aggressive chemical conditions.
Another concern is motor safety. A standard motor may not be suitable for an area containing flammable gases or vapours. Selecting a pump without checking the hazardous-area classification, chemical compatibility and operating conditions can lead to premature failure, leakage or unsafe operation.
The FRPP pump head provides corrosion resistance for many industrial acid and alkali applications. Its self priming chamber retains liquid to support suction-line evacuation during startup, reducing the need for repeated manual priming. The dry impeller sealing arrangement and internal impeller rod are designed to reduce chemical vapour exposure around the motor-side shaft area and help limit wear.
The one-piece moulded front cover allows convenient inspection and cleaning. For hazardous locations, an explosion-proof motor option can be specified according to the required protection standard and site classification. Alternative titanium or plastic fasteners can also be considered after checking the chemical composition and concentration.
| Model | Port (mm) | Phase | Poles | Power (HP) | 50 Hz Head (m) | 50 Hz Flow (L/min) | 60 Hz Head (m) | Weight (kg) |
|---|---|---|---|---|---|---|---|---|
| PD-40011L | 40 × 40 | 1 | 4 | 0.5 | 6 | 180 | 8 | 24/30 |
| PD-40012H | 40 × 40 | 3 | 2 | 1 | 13 | 240 | 13 | 25/31 |
| PD-40022H | 40 × 40 | 3 | 2 | 2 | 19 | 350 | 20 | 27/39 |
| PD-40032H | 40 × 40 | 3 | 2 | 3 | 25 | 400 | 28 | 31/43 |
| PD-50032H | 50 × 50 | 3 | 2 | 3 | 23 | 400 | — | 31/43 |
| PD-50052H | 50 × 50 | 3 | 2 | 5 | 26 | 450 | 32 | 42/55 |
| PD-75052H | 75 × 75 | 3 | 2 | 5 | 26 | 750 | 33 | 43/56 |
| PD-75072H | 75 × 75 | 3 | 2 | 7.5 | 26.5 | 900 | 39 | 52/65 |
| PD-75102H | 75 × 75 | 3 | 2 | 7.5 | 28 | 960 | 40 | 58/68 |
Note: Performance values are reference specifications. Confirm the pump curve, operating point, voltage, frequency, motor protection and weight configuration with the supplier before ordering.
This FRPP chemical self priming pump can be used in:
For abrasive, suspended-solid or slurry applications, confirm the allowable particle size and concentration before selection.
A self priming pump retains a certain amount of liquid inside its casing after shutdown. When the motor starts, the rotating impeller mixes the retained liquid with air in the priming chamber. The air is gradually discharged through the outlet, creating suction that draws additional liquid into the pump. Once the suction line is filled, the pump operates as a centrifugal pump to deliver liquid through the discharge pipe.
The self priming function depends on adequate retained liquid, airtight suction connections and the specified suction lift. The pump should not be operated continuously without liquid. Its sealing arrangement is designed to reduce exposure to chemical vapour around the shaft area, but correct installation and maintenance remain essential.
Confirm flow and head: Provide the required flow rate and total dynamic head. Select a model using its performance curve rather than maximum flow or head alone.
Check connection size: Match the 40 × 40 mm, 50 × 50 mm or 75 × 75 mm ports to the piping system.
Verify power supply: Confirm voltage, phase, frequency and motor power before ordering.
Check chemical compatibility: Provide the liquid name, concentration and temperature. FRPP and fastener materials must be suitable for all wetted and exposed components.
Assess hazardous-area requirements: Specify the gas or vapour classification and required explosion protection. Confirm the motor certification and complete pump configuration.
Review suction conditions: State the vertical suction lift, pipe length, fittings and liquid level. These factors affect actual self priming performance.
1. Can this FRPP pump transfer acid and alkali liquids?
Yes. It is designed for many industrial acid and alkali applications. Compatibility must be checked against the chemical type, concentration, temperature and all wetted materials.
2. Is the pump supplied with an explosion-proof motor?
An explosion-proof motor is available as an option. Please specify the hazardous-area classification and required certification when requesting a quotation.
3. Does the pump need manual priming before every startup?
The self priming chamber retains liquid to support startup without external priming of the entire suction line. The casing must retain the required liquid, and the suction line must be airtight.
4. Can it handle electroplating wastewater containing particles?
It may handle limited fine particles, but it is not intended for large solids or heavy slurry. Confirm particle size, concentration and abrasiveness before selection.
5. Can the pump run dry?
No continuous dry running is recommended. Although the sealing arrangement may tolerate brief abnormal conditions, dry operation can damage internal components.
6. Which model is suitable for 400 L/min at 25 m head?
PD-40032H is listed at 400 L/min and 25 m head at 50 Hz. Confirm the actual duty point against the pump curve and system resistance before ordering.
7. Can the pump operate at 60 Hz?
Selected models have 60 Hz head data. Please confirm the matching 60 Hz flow rate, motor voltage and performance curve for the required model.