Quick Link
Quick Contact
Address
Room 13G, No. 888 Wanhangu Road, Jing'an District, Shanghai, China
Tel
86--13912788181
Our Newsletter
Subscribe to our newsletter for discounts and more.
This C S W type vane mist eliminator removes entrained droplets from upward gas in desulfurization towers, spray towers, absorption columns and distillation columns. Gas passes through zigzag blade channels; droplets cannot follow the sharp turns, impinge on the blade, coalesce and drain. C, S and W profiles with optional hooks balance efficiency, pressure drop and fouling resistance. Standard materials include PP, FRP, 304, 316L, 2205 and titanium TA2/TA10, matching wet FGD, chloride and corrosive duty. Automated blade forming gives uniform spacing, burr-free surfaces and clean joints. High open area supports 3.5–5.0 m/s face velocity at 35–150 Pa pressure drop. The open passage resists blocking in crystallizing service, where wire mesh blinds. Custom blade type, diameter, spacing and drainage are available for tower revamps and OEM projects.
Modern towers use high-performance packing and run at high gas velocity. Fine droplets are carried upward and out of the tower top, causing product loss, lower packing efficiency, downstream contamination, visible plumes and emission exceedances. In desulfurization and scrubbing towers, carryover also causes corrosion and re-emission of absorbed pollutants. Many plants try wire mesh pads first, but mesh blinds in dirty or crystallizing service and creates high pressure drop.
The vane mist eliminator uses a mechanical, non-blocking design. Gas passes through a zigzag blade channel; droplets cannot follow the sharp turns, so they hit the blade, coalesce and drain down. C, S and W profiles, with or without hooks, trade off efficiency, pressure drop and fouling resistance. Uniform spacing prevents bypass. The large open area handles high gas velocity at low pressure drop. Material choice matches the chemistry: PP and FRP for acid and seawater, 304 and 316L for general chemical service, 2205 for chloride stress corrosion, and titanium for aggressive chloride or oxidizing conditions.
| Parameter | Specification |
|---|---|
| Product Type | Vane mist eliminator, baffle mist eliminator, wire mesh demister |
| Blade Types | C, S, W, hooked C/S/W, edge-sealed, corrugated |
| Materials | PP, FRP, 304, 304L, 316L, 2205, titanium TA2/TA10 |
| Pressure Drop | 35–150 Pa (crystallizing duty) |
| Face Velocity | 3.5–5.0 m/s |
| Customization | Material, blade type and dimensions |
| Packaging | Wooden pallet or wooden case |
| Applications | Desulfurization, spray, distillation, absorption towers |
Chemical, pharmaceutical, metallurgical, petroleum, coal chemical and wastewater plants, plus food, textile, marine and mining duty. Typical positions include tower top of desulfurization and spray towers, distillation and vacuum columns, absorption and stripping towers, evaporators and scrubbers — wherever mist must be removed before gas leaves the unit.
Gas flows upward through the blade channels, each forcing at least two sharp direction changes. Droplets with inertia cannot follow the gas stream, so they impinge on the blade wall, merge into a film and drain by gravity. Hooked blades add a pocket that traps re-entrained droplets. Clean gas leaves with low residual mist. Because the passage is open, dust and crystals pass through instead of blinding the element — the key advantage over wire mesh in crystallizing service.
Define gas velocity; vane efficiency depends on staying within 3.5–5.0 m/s.
Check the duty: clean gas favors S or hooked profiles; dirty or crystallizing gas favors W or wide-spaced C profiles.
Select material by chemistry: PP or FRP for acid, 304 or 316L for general service, 2205 for chlorides, titanium for severe corrosion.
Confirm the 35–150 Pa pressure drop budget.
Define diameter, blade spacing, drainage and cleaning access.
Decide whether a pre-stage or wash system is needed.