Quick Link
Quick Contact
Address
Room 13G, No. 888 Wanhangu Road, Jing'an District, Shanghai, China
Tel
86--13912788181
Our Newsletter
Subscribe to our newsletter for discounts and more.
This structured corrugated packing is an ordered packing for distillation, absorption and scrubber towers. It comes in three families: metal sheet in 304, 316L, 321, 2205 and carbon steel; ceramic for high temperature and strong acids; and plastic in PP, PE,PVDF and PTFE. Each is available as Y type with 45-degree corrugation or X type with 30-degree, from 125 to 700 specific surface area. The perforated plate and corrugation define the gas and liquid path, removing channeling and wall flow, wetting the surface evenly and raising mass transfer at low pressure drop. PP, PVC and FRP honeycomb tube settlers are also supplied for water clarification. Custom block dimensions, material grades and surface areas are made to match existing tower internals and revamp projects.
Corrugated Structured Packing for Industrial Scrubbers

Random or poorly selected packing causes real operating losses. Liquid channels down the wall, so part of the surface stays dry and outlet concentration rises. Pressure drop climbs and the blower reaches its limit. In hot or acid service, metal corrodes and plastic softens, while random packing compresses and loses void ratio. In water treatment, a plain settling tank needs a large footprint. These problems trace back to undefined flow paths, wrong material selection, and ignoring the pressure drop and flooding budget.
Ordered corrugated packing fixes this by defining the flow path. The corrugation alternates layer by layer, so gas and liquid are split, turned and remixed at every boundary; perforations and texture add lateral mixing and renew the film. Y type at 45 degrees gives higher capacity and lower pressure drop; X type at 30 degrees gives higher efficiency per metre. Metal suits most chemical duty; ceramic 1000°C and strong acid; plastic dilute acid and alkali at moderate temperature. Tube settlers increase settling area and cut footprint.
Structured Packing Installed in Industrial Absorber Towers

| Type | Material | Model | Specific Surface Area (m²/m³) | Void Ratio (%) | Bulk Weight (kg/m³) |
|---|---|---|---|---|---|
| Metal Sheet | 304, 304L, 321, 316, 316L, 2205, carbon steel | 125Y–500Y, 125X–500X | 125–500 | 92–98 | 53–180 |
| Ceramic | Ceramic | 125Y–700Y | 125–700 | 72–90 | 320–650 |
| Plastic | PP, PE, PVDF | 125Y–500Y, 125X–500X | 125–500 | 92–98 | 37.5–150 |
| Honeycomb Tube | PP, PVC, FRP | φ35, φ50, φ80 | Settling area by tube size | 60° installation | 1000×1000×886 mm |
| PTFE | Polytetrafluoroethylene | 125Y/250Y/350Y 450Y/500Y/700Y |
125–700 | 92–98 | 37.5–150 |
Distillation, absorption, stripping and scrubbing towers in chemical, petrochemical, fine chemical, pharmaceutical, coking and coal chemical plants; flue gas desulfurization and waste gas absorption; and water clarification with tube settlers.
Gas rises and liquid falls through the corrugated channels. Each layer turns the flow, so the phases contact on a thin, renewed film. The perforated plate lets gas and liquid cross between channels, equalizing distribution. Because the path is ordered, the bed runs at low pressure drop and high capacity without channeling. In the tube settler, water flows up inclined hexagonal channels; particles settle and slide down.
250Y and 350Y Structured Packing Options

Select material by chemistry and temperature: 304 or 316L for general duty, 321 for higher temperature, 2205 for chlorides, carbon steel for non-corrosive duty, ceramic for 1000°C or strong acid, PP/PE/PVDF for dilute acid and alkali.
Choose Y for capacity, X for efficiency.
Pick surface area: 125–250 for high liquid load and fouling, 350–500 for clean high-efficiency duty, up to 700 for ceramic fine separation.
Check pressure drop and flooding margin.
Confirm tower diameter, bed depth and distributor.
For water treatment, select tube diameter 35, 50 or 80 mm.
1. What is the difference between Y and X type?
Y type has 45-degree corrugation for higher capacity and lower pressure drop; X type has 30-degree corrugation for higher efficiency per metre.
2. Which material handles 1000°C and strong acid?
Ceramic packing, which keeps its structure and resists most inorganic acids at that temperature.
3. Can stainless steel packing handle chlorides?
304 is not recommended; 316L is limited, 2205 is better, ceramic is preferred for high chloride or wet chlorine.
4. What pressure drop does metal packing create?
About 140–400 Pa depending on model and load, with Y type lower than X type at the same size.
5. What is the plastic temperature limit?
PP, PE and PVDF suit dilute acid and alkali at moderate temperature; confirm the grade against actual gas temperature.
6. Can size and material be customized?
Yes. Model, specific surface area, material grade and block dimensions are made to the tower design.
7. How do I replace packing in an existing tower?
Provide the existing block dimensions, model and material. We manufacture direct-fit replacement blocks and can supply a mixed layer to match your original design.